Mobeye Argos Smoke Detector
The Mobeye smoke detector is manufactured by market leaders E.I and utilises the Ei 605TYC Optical detector.
Smoke detector for use with Mobeye i200 Argos battery
powered wireless alarm system.
- 10 Year Lithium cell will outlast the useful lifespan af the detector
- EN14604:2005 3rd Party approved
- Early detection of all standard domestic fire types
- Built-in high audibility warning sounder
- Large, easy to use Test / Hush button
- Hush feature allows false alarm control
- Easy to install twist-on base design
- Aesthetically pleasing, compact design
- Innovative and robust optical chamber design
- 5 year guarantee
The Ei605TYC is an Optical Smoke Alarm using the light scatter principle, giving a quick response to all standard domestic fire types.
There is no requirement to replace cells as the Lithium cells will power the alarm for more than 10 years. The non replaceable cell and tamperproof design limits the possibility of the alarm being disabled.
The Ei605TYC is designed for simple installation, commissioning and maintenance
The Ei605TYC has a large, easy to use, combined Test/Hush button enables full testing of the alarm and the ability to silence false alarms.
The Ei605TYC has an innovative high performance optical chamber with integral fixed insect screen reducing the possibility of false alarms.
The Ei605TYC maybe hardwire interconnected to twelve battery powered alarms enabling all alarms to sound if just one of the interconnected alarms should be triggered.
The Ei605TYC modular design allows it to be upgraded for functionality with the addition of the Ei605MTYRF Radio frequency module.
The smoke detector will activate the built in sounder upon sensing smoke particles. It will automatically reset and silence the alarm when the smoke particles are no longer present in the chamber.
The red indicating LED will flash once every 40 seconds to show that the alarm is powered and it has performed an automatic self-test.
The built in sounder will provide a minimum sound output of 85dB at 3m.
Pressing and holding the “Test/Hush” button will perform a self test and sound the horn – checking the chamber, electronics and horn.
Momentarily pressing the “Test/Hush” button when an alarm is sounding will set the alarm into “HUSH” mode. This reduces the sensitivity for a period of 10 minutes, after which the alarm automatically resets – providing control over false alarms.
The alarm is not powered until it is connected to the twist on base, thus avoiding battery power consumption during storage and prior to installation.
Do not install the actual smoke/heat alarm itself in new or renovated buildings until all work is completed (including floor coverings) and the building has been fully cleaned. (Excessive dust and debris from building work can contaminate the smoke chamber and cause problems, and it will also invalidate the guarantee). If it must be installed, cover it completely, particularly around the edges, with a dust cover (eg. a plastic bag), until all cleaning is finished.
Sensor: Optical, uses light scatter from smoke particles
Sensitivity: Complies with the requirements of BS EN 14604: 2005
Airspeed: Essentially immune to the effect
Button Test: Simulates the effect of smoke to
check the chamber, electronics and horn.
Hush: Silences nuisance alarm. Automatically resets after approximately 10 minutes.
Supply Voltage: 10 Year Lithium Cells with 2,000mAh capacity.
Power-On Indicator: Red LED flashes through cover every 40 seconds
Alarm: Piezoelectric-horn (built-in)
Alarm Sound Output: 85dB (minimum) at 3m
Temperature Range: 0 to 40°C
Humidity Range: 15% to 95% Relative Humidity – non condensing
Interconnect: Hardwire interconnect up to 12 battery powered alarms.
A combination of up to 12 battery and Mains powered alarms maybe interconnected.
Fixing: Screw fixings supplied
Dimensions: 115mm (diameter) x 45mm (height)
Weight: 200 grams
Warranty: 5 year (limited) warranty
Approvals: VdS approved to BS EN14604:2005, CE approved, Manufactured to ISO 9001:2000 quality standards.